INTRODUCTION
C-200 is a white pigmented temporary protective coating designed for use on spray booth walls. The white film provides a light reflective surface for better working conditions and the dried film is readily peelable enabling a heavy paint overspray to be quickly and cleanly removed.
C-200 is heat stabilised for use in low bake spray booths and will withstand temperatures up to 180ºC.

METHODS OF USE
Use as supplied first stirring thoroughly to disperse and settle pigment.
Spray using normal spraying equipment and techniques, pot pressure 40 psi, air pressure 60/80 psi and using a 70 thou spray gun nozzle.
Apply a double pass, wet on wet to give a dense white film. Do not use suction feed guns. Equipment can be easily cleaned with C.T.S thinners Ref. C-210.

COVERAGE
2-3 Square metres/litre at 2-3 thou dry film thickness.

PRECAUTIONS
C-200 is highly flammable and subject to petroleum regulations.
Harmful is inhalation therefore use under conditions of good ventilation.
Keep away from sources of ignition -NO SMOKING
Take precautionary measures against static discharges.
After use store container in a well ventilated area and keep at ambient temperatures.
Ensure that after use drums are tightly lidded.
The drums will be hazardous even when empty therefore continue to observe all precautions.
Do not empty into drains.
Avoid contact with the eyes, in the event of an accident irrigate eyes for 15 minutes and obtain medical attention.
In the event of fire use alcohol foam or dry chemical to extinguish.
In the event of spillage eliminate all sources of ignition and absorb into earth or soil.
Supplied in a 25 litre non returnable drums.

INTRODUCTION
C-220 is a toluene free white pigmented temporary protective coating for use on spray booth walls.
The white film provides a light reflective surface for better working conditions and the dried film is readily peelable, enabling heavy paint overspray to be quickly and cleanly removed.
C-220 is heat stabilised for use in low bake spray booths and will withstand temperatures up to 82°C.

METHODS OF USE
Use as supplied, first stirring thoroughly to disperse any settled pigment.
Spray using normal spraying equipment and techniques: pot pressure 1.5 bars or 0.13kg per cm2: air pressure = 2.7/3.3 bars or 0.25/0.32 kg per cm2 : and using a 2mm spray gun nozzle.
Apply a double pass, wet on wet, to give a dense white film.
Equipment can be easily cleaned with cellulose thinners.
Do not use suction feed guns.

COVERAGE
2-3 square metres/litres = 0.5/0.76 mms dry film thickness.
Supplied in 25 litre non-returnable drums.

INTRODUCTION
C-230 is a white pigmented water based temporary protective coating, designed for use on spray booth walls. The white film provides a light reflective surface for better working conditions, and the dried film is ready peelable enabling heavy paint overspray to be quickly and cleanly removed.

METHODS OF USE
Shake or stir well before use. Use as supplied and apply through pressure fed spray equipment using the following conditions:
The internal bore of the fluid pipe should be 12mm diameter to allow a rapid through put of material.
The fluid tip should be a least 2.8mm.
The fluid pressure should be around 40 psi. the air pressure should be around 60-80 psi.
Before use, ensure that the equipment is clean and free from thinners as this will cause coagulation of the emulsion. After use clean all the equipment with water.

COVERAGE
Using a double pass application a dry film thickness of 3 to 4 thou. Should be achieved which will give a coverage of approx. 2-3 hours with good air circulation and at normal room temperature.

PRECAUTIONS
CC-230 is non-flammable, non-corrosive and of very low toxicity. However it is recommended that the following precautions be observed:
Use under conditions of good ventilation.
Use a particle filter mask when spraying.
Avid eye contact, in the event of an accident, irrigate eyes thoroughly with water.
Avoid continual skin contact. PROTECT FROM FROST.
Supplied in 25 litre non-returnable drums.

INTRODUCTION
C-240 is a viscous liquid which when applied to non-solvent sensitive surfaces such as concrete, terrazzo, quarry tile or granolithic floors will dry to give a tough, non-slip, opaque peelable film. It is designed to maintain and protect the surface from abrasion and spillages of oil, paint, resins and dilute acids and alkalies.

METHOD OF USE
C-240 may be used as supplied, applied by brush, lambswool or mohair roller. Two coasts are recommended to ensure that a thick even film is applied, which will make it easier to remove after service.
C-240 may also be sprayed for such applications as the protection of components (of a non- solvent sensitive type) during fitting, transportation or storage. When applying by spray it will be necessary to add 20% C-210 Low Flash Thinners to ease spraying.
Equipment for spraying should be a pressure system using a 70 thou fluid tip set up. Thoroughly stir before use. C-210 thinners will be required to clean the equipment after use. If unsure of solvent sensitivity of a surface to be protected, patch test or contact C.T Supplies Ltd, for technical advice.

MAIN FEATURES
Good abrasion and chemical resistance
Quick easy method of keeping floors clean
Tough enough to withstand heavy traffic
Cleans surfaces on removal of the film

COVERAGE
To ensure that a good easily peelable film is produced, the maximum coverage should be 1 square per metre.

LIFE EXPECTANCY
Provided the film thickness is as recommended, the life expectancy of the protective film is as follows: Under indoor conditions out of direct sunlight a film life of 12 months can be expected. Under U.K outdoor weather conditions a film life of 6 months can be expected, although a periodic inspection is advisable.
C-240 Peelable Floor Coating and C-120 Low Flash Thinners are both supplied in 25 litre non-returnable drums.

INTRODUCTION
C-250 is a clear, water based peelable protective coating, designed to be easily peelable from glass, paint plastic and other non-porous surfaces to protect them from paint over spray or accidental damage.

METHOD OF USE
C-250 is used as supplied and is applied by brush, roller or pressure spray.

A wet film thickness of 5-6 thou is usually sufficient.

Please refer to our material safety data sheet for further details

INTRODUCTION
C-260 is a viscous liquid which when applied to non-solvent sensitive surfaces such as glass, metals, concrete etc. will dry to give a tough opaque protective peelable film.
It is designed to protect surfaces from abrasion and spillages from oil, paint, resins and dilute acids and alkalies.

METHOD OF USAGE
C-260 may be used as supplied, applied by a brush or roller. Two coats are recommended to ensure an even film is achieved which will make it easier to remove, when required.
Alternatively it may be thinned down with C.T.S Thinners, Ref. C-120, and sprayed onto the surface.
Details of spray equipment required are available o request.

MAIN FEATURES
Good abrasion and chemical resistance.
Easily peelable.
Clean surfaces on removal of film.

COVERAGE
To ensure that s good, easily peelable film is produced, the maximum coverage should be 2-3 square metres per litre.

LIFE EXPECTANCY
Provided the film thickness is as recommended the life expectancy of the protective film is as follows: Under indoor conditions out of direct sunlight a film life of 12 months can be expected. Under U.K outdoor weather conditions of 6 months can be expected, although a periodic inspection is advisable.

HOW SUPPLIED
C-260 is supplied in 25 litre non-returnable drums.