Tel: +353 (1) 8010009 / 087 2255566
Fax: + 353 (1) 8352901

WIWA Injection Units
 

WIWA Injection Units – Inject HD 1 and Inject HD 2 WIWA Plural Component Gel Injection Unit – 2K-Inject 14025
WIWA INJECTION EQUIPMENT
WIWA Inject HD 1 / HD 2 new technology forresin injection The HD 1 and HD 2 injection units are especially suited for injecting low viscosity epoxy or polyurethane resins and both comply with the standards found in the German ZTV Riss codes. WIWA 2K-Inject 14025 mature technology for gel injection The newly developed WIWA plural component gel injection unit, 2K-Inject 14025, not only exhibits WIWA’s strength in design, but is also evidence of WIWA’s competence in structural preservation and environmental consciousness. Setting new standards for equipment used in structural preservation
2K-Inject 14025
Fixed mixing ratio
Easy to operate
Highly accurate metering
Compact design
Inject HD 1 / HD 2
Powerful
Easy to operate
Ideal for working from scaffolds, in shafts or in tunnels
Freely adjustable injection pressure
Complies with the German ZTV Rissstandards
Mixing block complete with staticmixer and separate flush assemblyfor the A and B components
Professional sealing of a floor slabagainst water penetration using aplural component acrylate gel
POWERFUL AND VERSATILE
INJECT HD 1 / HD 2
WIWA Inject HD 1 & HD 2 Advanced technology Compact, portable and powerful pneumatic injection equipment The WIWA Inject HD 1 and HD 2 are especially suited for injecting low viscosity epoxy or polyurethane resins The WIWA Inject HD 1 and HD 2 are easy to use and transport, making them ideal if working from a scaffold or in a shaft or tunnel Both units comply with the standards found in the German ZTV Riss codes Listening to the motor will signal to the operator how close the injection process is to completion. As soon as the motor stops, the hole is filled The injection pressure is freely adjustable The advantage of air-driven piston pumps compared toelectric drivendiaphragmpumps is the fact that the air motor stops running when each hole is full This means: less wear and no thermalreaction caused by pumping resin from one container to another, thus avoiding a shorter pot life due to increased resin temperature. Inject HD 1 Basic Version The WIWA Inject HD 1 is delivered with a 7.5 m (24.6 ft.)
The WIWA Inject HD 1 is equipped with a feed funnel for approx. 1.5 liters(3 pints) of resin and an injection flance.including an injection lance
The WIWA Inject HD 2with 6 liter (1.5 gallon)feed funne
high-pressure injection hose,including an injection lance with coupling. 1.5 liters (3 pints) of injection resin. The complete pump is mounted to a sturdy frame. Inject HD 2 Basic Version The WIWA Inject HD 2 is delivered with a 7.5 m (24.6 ft.) high-pressure injection hose, including an injection lance with coupling. Furthermore, the unit is fitted with a feed funnel for approx. 6 liters (1.5 gallons) of injection resin. The complete pump is mounted to a sturdy frame. Accessories: Injection gun including fluidhose, hydraulic coupling and pressure gauge Order No.: 0631424
The WIWA Inject HD 2 with 6 liter (1.5 gallon) feed funnel
TECHNICAL SPECIFICATIONS WIWA Inject HD1 WIWA Inject HD 2
Pressure ratio:
33 : 1 33 : 1
Max. free-flow output:
3 l/min (.8 gal./min.) 3 l/min (.8 gal./min.)
Max. operating pressure:
264 bar (3828 psi) 264 bar (3828 psi)
Max. inbound air pressure:
8 bar (116 psi) 8 bar (116 psi)
Output per cycle:
14 ccm (.47 fl.oz.) 14 ccm (.47 fl.oz.)
Gross weight:
8 kg (17.6 lbs.) 9 kg (19.8 lbs.)
Feed funnel capacity:
1.5 l (3 pts.) 6 l (1.5 gal.)
Order No.
0644426 0644517
MATURE MACHINE TECHNOLOGY FOR ENVIRONMENTALLY FRIENDLY ACRYLATE GELS
2K-INJECT 14025
The newly developed WIWA 2K-Inject 14025 plural component injection unit for gel not only exhibits WIWA’s strength in design, but is also evidence of WIWA’s competen ce in structural preservation and environmental consciousness. Due to the fact that acrylate gels are not reliant upon the use of organic solvents, they are environmentally sound and can be processed easily and accurately using the WIWA 2K-Inject 14025. Typical applications for this pneumatic system are sealing cellar walls against backwater or seepage, providing a horizontal barrier against moisture and/or sealing other large surfaces that come into direct contact with the ground, such as tunnels, shafts or channels, thus solidifying the surrounding earth. The compact design and easy handling make this new plural component injection unit perfect for sealing areas in hard to reach places. The 1 : 1 mixing ratio is very accurate and can be maintained easily over long periods of operation.
A frame mounted flush pumpensures that the system canbe cleaned quickly and easily, avoiding hardening of any residue gel within the lines or mixing block. Optional accessories:
Description
Order No.
Mixing valve complete with static mixer and individual flushing arrangement for the A and B components
0642617
Alternative:Mixing valve complete with static mixer and flush arrangement
0641950
Coupling
0641973
Male adapter
0210854
Hydraulic connection
0411302
Male adapter
0218820
Slide coupling
0641197
Male adapter
0218820
Mounting kit for circulation
0641970
Mounting kit for feed funnels
0643529
Mounting kit for suction hose
0641933
Suction hose* NW4, 7.5 m (25 ft.)
0638610
*WARNING: 3
hoses are required total System advantages:  Air driven plural component
2K-Inject 14025 Basic Version High-pressure pump Flush pump Cart frame Flush pump suction hose System advantages: Air driven plural component injection unit for processing and for processing sealant gels and resins Fixed 1: 1 mixing ratio Non-stop, even flow of material Precise mixing results Easy to operate Separate flush pump Extremely compact, cart mounted
TECHNICAL SPECIFICATIONS 2K-Inject 14025
Pressure ratio:
25 : 1
Max. operating pressure:
200 bar (2900 psi)
Max. inbound air pressure:
8 bar (116 psi)
Output per cycle:
86 ccm (2.9 fl.oz)
Order No.
0641976

 

Little Pro 540
WIWA Profit
WIWA Phoenix
WIWA Magnum
Little Pro 400
Airlessco SL 1100
Developed by Barrowvale Technology Web Design Ireland. Copyright © Barrowvale Technology Ltd 2004. All rights reserved.